Windows系统下（Linux和MAC系统下请自行了解清楚）NI的各种软件、模块、工具包、驱动程序，使用NI许可证管理器来激活的，绝大部分的都可以使用NI Lincense Activator来激活，以下链接可下载：
NI序列号Serial Number生成激活工具NI License Activator，LabVIEW/VBAI/VDM/VAS等软件模块工具包破解工具不限版本
http://pcmv.cn/thread-490-1-1.html
视觉论坛的各种资源，除了视觉相关的模块有使用外，大部分的都不会使用，所以仅提供资源不能提供技术支持。资源的下载地址一般会同时提供NI官方地址和百度网盘的下载地址。某些工具包NI的地址失效或没有NI的下载地址，那视觉论坛也没有办法，只能尝试使用百度网盘地址下载；如果百度网盘的下载地址失效过期，可联系论坛客服更新。现在NI的下载服务器对我国IP地址不是很友好，有些时候速度很慢或大的资源下载很容易出错，这样会造成安装过程各种类型报错而无法安装。建议在下载完成后，对下载资源做校验和验证（NI一般会提供MD5或SHA256等），与官方或视觉论坛提供的校验和对比，一致就可以安装，如果不一致，则需要重新下载。视觉论坛早期下载的资源，那时候NI没有这么多限制，基本上都是正常下载的资源；后期下载的资源，都与NI的正确校验和对比过，保证是正确的资源才上传到百度网盘，所以百度网盘的资源基本上是正确的。校验和工具下载地址：
文件Hash计算器FHash,文件校验和验证下载文件正确性验证，MD5值计算、SHA1值计算、SHA256值计算、CRC32值计算
http://pcmv.cn/thread-26524-1-1.html
NI-DAQmx 9.3 Full Download Windows32/64中文/德语/日语/法语/英文/韩语 NI-DAQmx9.3完整版下载
NI-DAQmx
NI-DAQmx为使用NI数据采集和信号调理设备的客户提供支持。
NI-DAQmx驱动程序可控制数据采集系统的各个方面，包括信号调理、LabVIEW配置到编程，以及底层OS和设备控制。驱动程序提供的测量专用VI、函数、数据类型和分析集成可帮助您轻松创建应用程序，而优化的DMA数据传输和单点I/O则可让您快速进行准确的测量。
9.3
文件大小: 1277488193 字节 (1.19 GB)
修改日期: 2019-06-25 03:06
MD5: 5608c865881bdc5c4ff2e9faab348f4e（官方正确）
SHA1: 73b57c6f7798fc71fbf83140c2eacd5b211f81a4
SHA256: f82308e318327702260abeb8cfb39b4389033cc4c7e1f0b1b4b9f8f11795d178
CRC32: 97e4075a
NI-DAQmx 9.3 Full Download Windows32/64中文/德语/日语/法语/英文/韩语 NI-DAQmx9.3完整版下载
http://pcmv.cn/thread-25330-1-1.html?fromuid=9
(出处: 视觉论坛VISIONBBS|视觉之家VISIONHOME)
NI-DAQmx 9.3 Readme
February 2011
Thank you for using NI-DAQmx, version 9.3. The readme contains the following main sections:
New features added in NI-DAQmx 9.3
Important Notice: Microsoft Hotfix for USB DAQ Devices and Windows XP
Fixed issues
NI-DAQmx considerations
Upgrade considerations
Software support in NI-DAQmx 9.3
Device support in NI-DAQmx
System requirements
New Features Added in NI-DAQmx 9.3
The following features were added in NI-DAQmx 9.3:
Support for the NI cDAQ-9171 USB chassis and the NI cDAQ-9181 Ethernet chassis.
Support for external calibration in CompactDAQ with the NI 9217, 9225, and 9227 C Series devices.
Support for the NI 2571 switch module.
TDMS usability enhancements.
Important Notice: Microsoft Hotfix for USB DAQ Devices and Windows XP
If you are using NI-DAQmx with a USB DAQ device on Windows XP, you should install the Microsoft hotfix reported in Microsoft Knowledge Base 969238.
Fixed Issues
The following issues were fixed in NI-DAQmx 9.3:
| CAR ID | Summary |
| 106314 | Shunt cal and offset null in a strain task do not work properly if a custom scale is selected |
| 187820 | NI USB-4431 may output stale data at the start of a task if the sample rate has changed from the last task's rate |
| 206282 | Starting an AO task on an NI USB-4431 causes a glitch on the channel |
| 235725 | The NI WLS-9163 may experience connection issues with international wireless routers |
| 239962 | Starting an acquisition using multiple NI 9219 devices takes 10-20 seconds |
| 242484 | Explicitly committing a task with events on a simulated cDAQ chassis can result in a system crash |
| 242611 | NI 9203 may return improperly scaled data with an NI 9174, 9178, or 9188 chassis when mixing bipolar and unipolar channels |
| 245504 | NI USB-4431 doesn't support DAQmxGetWriteTotalSampPerChanGenerated property |
| 246579 | DAQ Assistant hangs when creating a digital NI-DAQmx task from a LabVIEW Project |
| 246651 | Master Timebase cannot be shared between tasks in a cDAQ chassis |
| 248436 | Using the DAQ Assistant to calibrate a strain channel on the NI 9235/6 gives error -200077 |
| 249685 | Scaled units for acceleration measurement type should support in/s^2 |
| 250609 | NI-DAQmx Test Panels Are Taller Than 600 Pixels |
| 251790 | NI LabVIEW SignalExpress 2010 freezes when generating a calibration report |
| 252395 | Repeatedly creating, starting, stopping, and clearing AO tasks on an NI 4461 may cause it to output full scale noise |
| 252811 | Setting timeout to -1 can timeout with a Frequency Measurement DAQmx Global Virtual Channel |
| 253284 | NI USB-4431 AO tasks do not stop generating at task stop when "Allow Regeneration" and "Use Only Onboard Memory" are enabled |
| 255249 | NI USB-4431/32 inputs invert the polarity of out of range voltage signals |
| 277095 | Value of DAQmx Channels to Read property changes when you modify other NI-DAQmx properties |
| 278121 | NI WLS-9163 may become unresponsive during long-term use |
| 278249 | NI USB-4431 AO to AI synchronization may vary when the unit is power cycled |
| 278838 | NI USB-4431 may output data from previous tasks if continuous AO tasks are stopped and restarted |
| 279016 | NI USB X Series digital I/O lines glitch on Windows restart |
| 280611 | NI USB-4431 may not update the output for short finite output tasks |
| 281238 | In an NI 9172, on-demand digital output can tri-state other lines on the same NI 9401 |
| 282045 | Error -200152 may be reported repeatedly for NI ENET-9163 or NI WLS-9163 devices |
| 282383 | C Series modules used with the NI WLS/ENET-9163 may return corrupted data in adverse network conditions |
NI-DAQmx Considerations
This section covers known issues and considerations specific to NI-DAQmx.
Microsoft Silverlight Required for NI cDAQ-918x Configuration
The NI cDAQ-918x configuration, both with the NI Web-based configuration and in MAX, requires Microsoft Silverlight. Silverlight is available from microsoft.com/silverlight. To find out more about using Microsoft Silverlight with NI software, visit ni.com/info and enter the info code Silverlight.
NI cDAQ-918x Works Incorrectly if Path Includes Non-ASCII (Multi-Byte) Characters
The NI cDAQ-918x might not function correctly if NI-DAQmx is installed in a path with non-ASCII (or multi-byte) characters. This issue most commonly affects NI-DAQmx installations on Korean, Japanese, and Chinese versions of Windows. If your NI-DAQmx installation path contains non-ASCII characters, uninstall NI-DAQmx and other NI application development software and then reinstall your software to a path without non-ASCII characters.
Web-Based Configuration for the NI cDAQ-918x Available Only for Windows and Macintosh
Web-based configuration is available for the NI cDAQ-918x by accessing the device in a Microsoft Silverlight-enabled Web browser via its host name or IP address. This support is only accessible from Windows-based or Macintosh-based systems. Refer to the chassis user guide for more information.
Firmware Update Required to Use NI cDAQ-9188 in NI-DAQmx 9.3
You must update the firmware on the NI cDAQ-9188 to use it with NI-DAQmx 9.3. Firmware files for Network DAQ devices are named ni<model number>fw.cfg (for instance, ni9188fw.cfg). You can obtain the latest version of firmware in the Firmware directory on the NI-DAQmx media or by going to ni.com/downloads.
Required Firmware Updates for Network DAQ Devices in NI-DAQmx
If you receive Error -201340, you need to update the firmware on your Network DAQ device. Firmware files for Network DAQ devices are named ni<model number>fw.cfg (for instance, ni9188fw.cfg). You can obtain the version of firmware supported by your version of NI-DAQmx by going to ni.com/info and entering the info code exkpzt. If you installed NI-DAQmx from a DVD, you can also find a compatible version in the Firmware directory on that DVD.
New Error Returned when Loading an Invalid Device Name
In NI-DAQmx 9.3 and later, an invalid device name returns Error –200220, kErrorInvalidDeviceID, instead of Error –200170, kErrorPhysicalChanDoesNotExist. This change has no impact on newly created applications but can affect existing applications if the applications are performing error checking by looking for the specific error number (–200170).
NI USB-4431 Specifications Changes
The NI USB-4431 specifications have changed. The AO offset is specified with a higher level of uncertainty. The analog inputs and outputs also have a higher gain uncertainty than previously specified. In particular, sample rates of less than 40 kHz result in an accuracy drop. The newest version of the NI USB-443x Specifications reflects these changes. A separate document, Notice of Specification Change - USB 4431, details these changes as well.
Aborting Single-Point Reads and Writes in LabVIEW
Single-point reads and writes do not respond to the Abort Execution button in LabVIEW.
Configuring MAX Strain Tasks
MAX strain tasks do not support configuring terminal configurations. By default, the configuration in MAX is differential. For the NI SC-2043-SG, the terminal configuration is NRSE. To avoid configuration issues, use the NI-DAQmx API to create the task.
DAQ Assistant Maximum Channel Count
The maximum number of channels you can have in a task created with the DAQ Assistant is 4096 channels.
NI DAQCard-6715 Analog Output
Hardware-timed single-point mode and hardware-timed nonbuffered mode are nonfunctional. Your application is using hardware-timed nonbuffered mode if you have set up a sample clock and a buffer size of 0, or set up a sample clock, but do not begin writing until after you start the task. All other waveform and static analog output modes work as expected.
NI ENET/WLS-9215 Times Out Unexpectedly
On the NI ENET/WLS-9215, an unexpected timeout can occur in continuous tasks using an external or very slow sample clock. The last sample may not be returned until the next sample clock pulse. To avoid the timeout, increase the timeout time (to allow the next sample clock pulse to occur) or acquire an even number of samples.
NI-DAQmx Events
Not all NI-DAQmx events will fire if the conditions for the event occur more quickly than the system can process.
Samples Not Acquired on NI 660x or NI 6624 Devices
When using pulse width, semi-period or two-edge separation buffered measurements with the NI 660x and NI 6624 on counters 0 and 1, some samples may not be acquired under certain circumstances.
Microsoft Windows 7/Vista and Visual Studio C++, C#, Visual Basic .NET, and ANSI C Examples
Running certain applications on Microsoft Windows 7/Vista requires administrator privileges, because the application name contains keywords such as setup, update, or install. To avoid this problem, you must add an additional manifest to the application that specifies the privileges required to run the application. Some NI-DAQmx ANSI C, Measurement Studio Visual C++, C#, and Visual Basic .NET examples include these keywords. Therefore, some examples for these application development environments include an additional manifest file that you must embed in the example executable.
In ANSI C, Measurement Studio Visual C++ , C#, and Visual Basic .NET, the manifest file is named [ExampleName].exe.manifest, where [ExampleName] is the NI-provided example name. The steps for embedding an example varies depending on the programming language. Refer to the comments included with affected examples for additional information.
Compiling Visual Studio 2005 examples can generate the following warning: manifest authoring warning 81010002: Unrecognized Element "requestedPrivileges" in namespace "urn:schemas-microsoft-com:asm.v3". For more information, refer to the Microsoft Feedback web page. This warning does not affect example execution and can be ignored. This warning happens because of the version of mt.exe that is shipped with Visual Studio 2005. The mt.exe tool embeds the additional manifest in the example executable.
Important: Performing these steps on Windows XP Service Pack 2 (SP2) may cause your computer to restart when you run the application. Refer to the Microsoft Knowledge Base entry for more information. To avoid a computer restart, build your application using Visual Studio 2005 SP1.
Upgrade Considerations
This section covers changes in NI-DAQmx functionality.
DAQmx Is Read or Write Late Obsoleted
The existing DAQmx Is Read or Write Late function/VI has been obsoleted and no longer has any effect. Applications that must check whether they are maintaining real-time behavior have two options. For the strictest checking, use the Wait for Next Sample Clock function/VI. Refer to your API reference help, such as the LabVIEW Help or the NI-DAQmx C Function Reference Help, for more information on this function/VI. To check only whether the application misses any analog input samples, set the Report Missed Samples property to True on the analog input task. In LabVIEW, the Report Missed Samples property is in the Real Time property node. For more details, National Instruments strongly recommends that you read the document referred to by the Wait for Next Sample Clock function/VI.
Duplicate Count Prevention Defaults
As of NI-DAQmx 7.4, the default setting for the duplicate count prevention attribute/property on M Series and TIO-based counters has been changed. This change affects all input counter operations, with the exception of single-point edge counting and position measurements. Duplicate count prevention is now on by default as long as the following conditions are met:
The duplicate count prevention attribute/property has not been explicitly set.
The selected counter timebase source is not set to an internal timebase.
The prescaler attribute/property has not been set.
The counter output event has not been configured.
To learn more, refer to Duplicate Count Prevention in the NI-DAQmx help.
Existing .NET Project Produces Build Errors
If you are using NI-DAQmx with a .NET language, an existing project can produce build errors from an assembly that is not referenced. To eliminate this error, add a reference to the NationalInstruments.Common assembly to the project.
Multichannel SCXI Convert Clock Default Rate Change in NI-DAQmx 8.5
Starting in NI-DAQmx 8.5, a delay of 20 μs was added to the fastest possible channel conversion rate on an SCXI chassis connected to a 16-bit or 18-bit E or M Series device. If a sample rate is set fast enough to require a convert clock rate greater than the default rate, warning 200011 is generated, informing the user that the accuracy of the measurement might be compromised. However, since this is a warning, the convert clock used is based on the rate needed by the sample clock set by the user (that is, convert clock = sample clock * number of channels).
For SCXI chassis containing a module with track-and-hold circuitry, 10 μs of padding is now added to the fastest possible conversion rate when connected to a 12-bit E Series device.
These changes ensure the most accurate data is being acquired. However, if the effect on the performance due to this change is too great (such as on an RT system using hardware-timed single point in a control loop), then the convert clock rate attribute can be explicitly set, overriding the default rate.
This change affects only multichannel acquisitions.
In versions prior to NI-DAQmx 8.5, only 10 μs of delay was added to the fastest possible channel conversion rate on an SCXI chassis without a track-and-hold module connected to any DAQ device. In these versions of NI-DAQmx, no warning was generated when the sample rate needed a faster convert clock than was chosen by default. When an SCXI chassis with a track-and-hold module was present, the convert clock rate selected was the fastest possible rate that the DAQ device can handle, up to 333 kHz.
NI PCI-6704 and PXI-6704 Current Output Accuracy
NI-DAQmx 8.3 changes the algorithm used to scale the 20 mA current outputs of the NI 6704 to a method that matches the behavior of Traditional NI-DAQ (Legacy). Previous versions of the NI-DAQmx driver use a second method.
The effect of the change is that when NI-DAQmx programs the 6704 to output current, the actual current level of the 6704 is 10 μA higher with NI-DAQmx 8.3 compared to previous versions of NI-DAQmx. The actual current output with NI-DAQmx 8.3 is the same compared to Traditional NI-DAQ (Legacy) drivers. This change has no effect on the voltage outputs of the 6704.
Because of this change, NI recommends that you externally calibrate NI 6704 devices with NI-DAQmx 8.3 (or later) before using devices with the NI-DAQmx 8.3 (or later) driver. NI 6704 devices that ship with NI-DAQmx 8.3 have already been calibrated with NI-DAQmx 8.3. For other NI 6704 devices, refer to the manual calibration procedure available at ni.com/calibration.
USB-9xxx Devices
Unplug your USB-9xxx and plug it back in or power the USB device down and up after upgrading NI-DAQmx. If the USB-9xxx is connected to a USB hub, make sure to disconnect the USB-9xxx from the hub, not the hub from the computer. Disconnecting power from the USB device causes installed devices to load the correct version of the firmware.
Virtual TEDS Data for the USB-9233/9237
If you connect hardware TEDS to USB-9233/9237 channels configured with virtual TEDS, the virtual TEDS will be replaced with hardware TEDS data after upgrading to NI-DAQmx 8.6 or later.
Software Support in NI-DAQmx 9.3Operating System Support
The following operating systems are supported in NI-DAQmx 9.3:
Windows 7 (32-bit and 64-bit)
Windows Vista Business edition (32-bit and 64-bit)
Windows XP, Service Pack 2 or greater
Windows Server 2003 R2 (32-bit)
Windows Server 2008 R2 (64-bit)
For OS-specific device support information, refer to ni.com/support/daq/versions.
Note Support for Windows Server 2003 R2 may require disabling physical address extensions (PAE). To learn how this might affect your use of Windows Server 2003 and what actions you might have to take, visit ni.com/info and enter the info code PAESupport.
| Caution If you plan to perform an upgrade of your system from a prior version of Microsoft Windows to Microsoft Windows Vista, you are required to uninstall all National Instruments software prior to performing the upgrade. After the upgrade has been completed, you can reinstall your National Instruments software. |
NI-DAQmx 9.3 supports Phar Lap only with the LabVIEW Real-Time Module 8.5 and later.
Windows 2000 users must use NI-DAQmx 9.1.1 or earlier.
To find and download an earlier version of NI-DAQmx that supports other operating systems, refer to ni.com/downloads.
NI-DAQmx does not support guest accounts on Windows 7/Vista/XP. You must log into an administrative or user account to use NI-DAQmx on these OSes.
NI Application Software Support
The following table lists the NI application software versions supported by NI-DAQmx. If you are not using NI application software, refer to Microsoft Visual Studio Support.
In NI-DAQmx 8.6 and prior, when you add the DAQ Component as a new item to your Visual Studio 2005 project, the DAQ Component is located in the Measurement Studio folder and the Visual Basic Items or Visual C# Project Items folders. In NI-DAQmx 8.7 and later, the DAQ Component is located only in the Visual Basic Items or Visual C# Project Items folder and named NI-DAQ Component.
| NI Application Software | Versions Supported by NI-DAQmx and the DAQ Assistant |
LabVIEW | 8.5.x, 8.6.x, 2009, and 2010 |
LabVIEW Real-Time Module | 8.5.x and later (including 2009 and later) |
LabWindows/CVI | 8.1 and later (including 2009 and later) |
LabWindows/CVI Real-Time Module | 8.1 and later (including 2009 and later) |
Measurement Studio | 8.1 and later (including 2009 and later) |
LabVIEW SignalExpress | 2.x and later (including 2009 and later) |
Measurement Studio Examples
The directories that the Measurement Studio examples install to depends on which component is installed, the version of Visual Studio or the .NET Framework the example supports, the version of Measurement Studio installed, and the operating system. For detailed information on examples for Measurement Studio, refer to Where To Find Examples in the NI Measurement Studio Help.
Microsoft Visual Studio Support
The following table lists the programming languages and Microsoft Visual Studio versions supported by NI-DAQmx.
| Programming Language | Visual Studio Versions Supported by NI-DAQmx |
|
ANSI C | 2003, 2005, 2008, and 2010 |
|
Visual C++ MFC1 | 20052 and 20083 |
|
.NET Framework 2.0 Languages
(C# and Visual Basic.NET) | 2005 |
|
.NET Framework 3.5 Languages
(C# and Visual Basic.NET) | 2008 |
|
.NET Framework 4.0 Languages
(C# and Visual Basic.NET) | 20104 |
|
Visual Basic 61 | 6 |
|
| 1 NI-DAQmx includes limited support for Visual Basic 6 and Visual Studio C++ MFC. For more information, visit ni.com/info and enter the info code daqmxvstudio. |
| 2 Requires Measurement Studio 8.0.1 — Measurement Studio 2009 |
| 3 Requires Measurement Studio 8.6 — Measurement Studio 2009 |
| 4 With Windows XP, Service Pack 3 or later is required |
Earlier versions of NI-DAQmx support other application software and language versions. To find and download an earlier version of a driver, refer to ni.com/downloads.
If you are using the DAQmx .NET Library, the .NET 2.0 Framework, .NET 3.5 Framework, or .NET 4.0 Framework is required.
NI-DAQmx 9.2 is the last release that includes full feature support for Visual C++ MFC 2005 and 2008.
If you are using the .NET Framework 1.1 or Visual C++ MFC 2003, you must use NI-DAQmx 9.1.5 or earlier. For more information on NI-DAQmx support for .NET Framework 1.1 or Visual C++ MFC 2003, including considerations for users upgrading from NI-DAQmx 9.1.5 or earlier, visit ni.com/info and enter the info code ex6rzd.
Device Support in NI-DAQmx
The following lists detail the devices supported in NI-DAQmx. Device support is divided into the following categories:
For OS-specific device support information, refer to ni.com/support/daq/versions.
For MXI-3 and MXI-4 OS-specific support information, refer to ni.com/kb and search for KnowledgeBase entry 45MA9LF7.
Devices Supported in NI-DAQmx
The following lists detail the devices supported in NI-DAQmx. Device support is divided into the following categories:
| Note In the device support tables that follow, a ✓ indicates that the device is supported, a blank cell indicates that the device either does not exist or is not supported in NI-DAQmx, and an X indicates that the device is no longer supported in NI-DAQmx. |
X Series DAQ
M Series DAQ
E Series DAQ
S Series DAQ
SC Express
C Series, Network DAQ, and USB DAQ
CompactDAQ Chassis
AO Series
Digital I/O
TIO Series
Dynamic Signal Acquisition
SC Series DAQ
Switches
SCXI Chassis
SCXI Modules
TEDS Interface
Academic Devices
Legacy DAQ Devices
Low-Cost USB Devices
For OS-specific device support information, refer to ni.com/support/daq/versions.
For MXI-3 and MXI-4 OS-specific support information, refer to ni.com/kb and search for KnowledgeBase entry 45MA9LF7.
X Series DAQ
The following X Series DAQ devices are supported:
| Device | PCIe | PXIe | USB |
| NI 6320 | ✓ |
|
|
| NI 6321 | ✓ |
|
|
| NI 6323 | ✓ |
|
|
| NI 6341 | ✓ | ✓ | ✓ |
| NI 6343 | ✓ |
| ✓ |
| NI 6351 | ✓ |
| ✓ |
| NI 6353 | ✓ |
| ✓ |
| NI 6356 |
| ✓ | ✓ |
| NI 6358 |
| ✓ |
|
| NI 6361 | ✓ | ✓ | ✓ |
| NI 6363 | ✓ | ✓ | ✓ |
| NI 6366 |
| ✓ | ✓ |
| NI 6368 |
| ✓ |
|
M Series DAQ
The following M Series DAQ devices are supported:
| Device | PCI | PCIe | PXI | PXIe | USB |
| NI 6210/11/12/15/16/18 |
|
|
|
| ✓ |
| NI 6220 | ✓ |
| ✓ |
|
|
| NI 6221 | ✓ |
| ✓ |
| ✓ |
| NI 6224 | ✓ |
| ✓ |
|
|
| NI 62251 | ✓ |
| ✓ |
| ✓ |
| NI 6229 | ✓ |
| ✓ |
| ✓ |
| NI 6230/32/33/36/38/39 | ✓ |
| ✓ |
|
|
| NI 6250 | ✓ |
| ✓ |
|
|
| NI 6251 | ✓ | ✓ | ✓ | ✓ | ✓ |
| NI 6254 | ✓ |
| ✓ |
|
|
| NI 62551 | ✓ |
| ✓ |
| ✓ |
| NI 6259 | ✓ | ✓ | ✓ | ✓ | ✓ |
| NI 6280 | ✓ |
| ✓ |
|
|
| NI 6281 | ✓ |
| ✓ |
| ✓ |
| NI 6284 | ✓ |
| ✓ |
|
|
| NI 6289 | ✓ |
| ✓ |
| ✓ |
| 1USB versions do not have NI-DAQmx simulated device capability. |
E Series DAQ
The following E Series DAQ devices are supported.
| Device | PCMCIA | PCI | PXI |
| NI 6023E |
| ✓ |
|
| NI 6024E | ✓ | ✓ |
|
| NI 6025E |
| ✓ | ✓ |
| NI 6030E |
|
| ✓ |
| NI 6031E |
| ✓ | ✓ |
| NI 6032E/33E/34E/35E |
| ✓ |
|
| NI 6036E | ✓ | ✓ |
|
| NI 6040E |
|
| ✓ |
| NI 6052E |
| ✓ | ✓ |
| NI 6062E | ✓ |
|
|
| NI 6070E |
|
| ✓ |
| NI 6071E |
| ✓ | ✓ |
| NI PCI-MIO-16E-1 |
| ✓ |
|
| NI PCI-MIO-16E-4 |
| ✓ |
|
| NI PCI-MIO-16XE-10 | X | ✓ |
|
| NI PCI-MIO-16XE-50 | X | ✓ |
|
S Series DAQ
The following S Series DAQ devices are supported:
| Device | PCI | PXI | PXIe |
| NI 6110 | ✓ |
|
|
| NI 6111 | ✓ |
|
|
| NI 6115 | ✓ | ✓ |
|
| NI 6120 | ✓ | ✓ |
|
| NI 6122 | ✓ | ✓ |
|
| NI 6123 | ✓ | ✓ |
|
| NI 6124 |
|
| ✓ |
| NI 6132 | ✓ | ✓ |
|
| NI 6133 | ✓ | ✓ |
|
| NI 6143 | ✓ | ✓ |
|
| NI 6154 | ✓ |
|
|
SC Express
The following SC Express devices are supported:
| Device | PXIe |
| NI 4300 | ✓ |
| NI 4330 | ✓ |
| NI 4331 | ✓ |
| NI 4353 | ✓ |
C Series, Network DAQ, and USB DAQ
The following C Series, Network DAQ, and USB DAQ devices are supported:
| Device | CompactDAQ Chassis1 | Legacy Chassis and Carriers |
| NI ENET/WLS-9163 | NI USB-9162 | NI cDAQ-9172 |
| NI 9201 | ✓ |
| ✓ | ✓ |
| NI 9203 | ✓ |
|
| ✓ |
| NI 9205 | ✓ | ✓ |
| ✓ |
| NI 9206 | ✓ | ✓ |
| ✓ |
| NI 9207 | ✓ |
|
| ✓ |
| NI 9208 | ✓ |
|
| ✓ |
| NI 9211 | ✓ | ✓ |
| ✓ |
| NI 9211A |
|
| ✓ |
|
| NI 9213 | ✓ | ✓ | ✓ | ✓ |
| NI 9214 | ✓ |
|
| ✓ |
| NI 9215 | ✓ | ✓ |
| ✓ |
| NI 9215A |
|
| ✓ |
|
| NI 9217 | ✓ |
|
| ✓ |
| NI 9219 | ✓ | ✓ | ✓ | ✓ |
| NI 9221 | ✓ |
| ✓ | ✓ |
| NI 9222 | ✓ |
|
|
|
| NI 9223 | ✓ |
|
|
|
| NI 9225 | ✓ |
|
| ✓ |
| NI 9227 | ✓ |
|
| ✓ |
| NI 9229 | ✓ |
| ✓ | ✓ |
| NI 9233 | ✓ |
| ✓ | ✓ |
| NI 9234 | ✓ | ✓ | ✓ | ✓ |
| NI 9234B | ✓ |
|
| ✓ |
| NI 9235 | ✓ |
|
| ✓ |
| NI 9236 | ✓ |
|
| ✓ |
| NI 9237 | ✓ | ✓ | ✓ | ✓ |
| NI 9239 | ✓ |
| ✓ | ✓ |
| NI 9263 | ✓ |
| ✓ | ✓ |
| NI 9264 | ✓ |
| ✓ | ✓ |
| NI 9265 | ✓ |
| ✓ | ✓ |
| NI 9269 | ✓ |
|
| ✓ |
| NI 9401 | ✓ |
|
| ✓ |
| NI 9402 | ✓ |
|
| ✓ |
| NI 9403 | ✓ |
|
| ✓ |
| NI 9411 | ✓ |
|
| ✓ |
| NI 9421 | ✓ | ✓ | ✓ | ✓ |
| NI 9422 | ✓ |
|
| ✓ |
| NI 9423 | ✓ |
|
| ✓ |
| NI 9425 | ✓ |
|
| ✓ |
| NI 9426 | ✓ |
|
| ✓ |
| NI 9435 | ✓ |
|
| ✓ |
| NI 9472 | ✓ | ✓ | ✓ | ✓ |
| NI 9474 | ✓ |
|
| ✓ |
| NI 9475 | ✓ |
|
| ✓ |
| NI 9476 | ✓ |
|
| ✓ |
| NI 9477 | ✓ |
|
| ✓ |
| NI 9478 | ✓ |
|
| ✓ |
| NI 9481 | ✓ | ✓ | ✓ | ✓ |
| NI 9485 | ✓ |
|
| ✓ |
| 1Does not include the NI cDAQ-9172. |
CompactDAQ Chassis
The following CompactDAQ chassis are supported:
| Device | CompactDAQ Chassis |
NI cDAQ-9171 | ✓ |
NI cDAQ-9172 | ✓ |
NI cDAQ-9174 | ✓ |
NI cDAQ-9178 | ✓ |
NI cDAQ-9181 | ✓ |
NI cDAQ-9188 | ✓ |
AO Series
The following AO Series devices are supported:
| Device | DAQCard | PCI | PXI |
| NI 6703 |
| ✓ |
|
| NI 6704 |
| ✓ | ✓ |
| NI 6711 |
| ✓ | ✓ |
| NI 6713 |
| ✓ | ✓ |
| NI 6715 | ✓ |
|
|
| NI 6722 |
| ✓ | ✓ |
| NI 6723 |
| ✓ | ✓ |
| NI 6731 |
| ✓ |
|
| NI 6733 |
| ✓ | ✓ |
Digital I/O
The following digital I/O devices are supported.
| Device | DAQCard | PCI | PCIe | PXI | PXIe | USB |
| NI 65011 |
|
|
|
|
| ✓ |
| NI 6503 |
| ✓ |
|
|
|
|
| NI 6508 |
|
|
| ✓ |
|
|
| NI 6509 |
| ✓ | ✓ | ✓ |
| ✓ |
| NI 6510 |
| ✓ |
|
|
|
|
| NI 6511 |
| ✓ |
| ✓ |
|
|
| NI 6512 |
| ✓ |
| ✓ |
|
|
| NI 6513 |
| ✓ |
| ✓ |
|
|
| NI 6514 |
| ✓ |
| ✓ |
|
|
| NI 6515 |
| ✓ |
| ✓ |
|
|
| NI 6516 |
| ✓ |
|
|
|
|
| NI 6517 |
| ✓ |
|
|
|
|
| NI 6518 |
| ✓ |
|
|
|
|
| NI 6519 |
| ✓ |
|
|
|
|
| NI 6520 |
| ✓ |
| ✓ |
|
|
| NI 6521 |
| ✓ |
| ✓ |
|
|
| NI 6525 |
|
|
|
|
| ✓ |
| NI 6527 |
| ✓ |
| ✓ |
|
|
| NI 6528 |
| ✓ |
| ✓ |
|
|
| NI 6529 |
|
|
| ✓ |
|
|
| NI 6533 | X | ✓ |
| ✓ |
|
|
| NI 6534 |
| ✓ |
| ✓ |
|
|
| NI 6535 |
|
| ✓ |
| ✓ |
|
| NI 6536 |
|
| ✓ |
| ✓ |
|
| NI 6537 |
|
| ✓ |
| ✓ |
|
| NI DIO-24 | ✓ |
|
|
|
|
|
| NI DIO-32HS |
| ✓ |
|
|
|
|
| NI DIO-96 |
| ✓ |
|
|
|
|
| 1Does not have NI-DAQmx simulated device capability. |
TIO Series
The following TIO series devices are supported:
| Device | PCI | PXI |
| NI 6601 | ✓ |
|
| NI 6602 | ✓ | ✓ |
| NI 6608 |
| ✓ |
| NI 6624 | ✓ | ✓ |
Dynamic Signal Acquisition (DSA)
The following DSA devices are supported:
| Device | PCI | PXI | PXIe | USB |
| NI 4431 |
|
|
| ✓ |
| NI 4432 |
|
|
| ✓ |
| NI 4461 | ✓ | ✓ |
|
|
| NI 4462 | ✓ | ✓ |
|
|
| NI 4472/B | ✓ | ✓ |
|
|
| NI 4474 | ✓ |
|
|
|
| NI 4492 |
|
| ✓ |
|
| NI 4495 |
| ✓ |
|
|
| NI 4496 |
| ✓ | ✓ |
|
| NI 4497 |
|
| ✓ |
|
| NI 4498 |
| ✓ | ✓ |
|
| NI 4499 |
|
| ✓ |
|
SC Series DAQ
The following SC Series DAQ devices are supported:
| Device | PXI |
| NI 4200 | ✓ |
| NI 4204 | ✓ |
| NI 4220 | ✓ |
| NI 4224 | ✓ |
Switches
The following switches are supported:
| Device | PCI | PXI | PXIe |
| NI 4021 | ✓ | ✓ |
|
| NI 2501 |
| ✓ |
|
| NI 2503 |
| ✓ |
|
| NI 2510 |
| ✓ |
|
| NI 2512 |
| ✓ | ✓ |
| NI 2514 |
| ✓ | ✓ |
| NI 2515 |
| ✓ | ✓ |
| NI 2527 |
| ✓ | ✓ |
| NI 2529 |
| ✓ | ✓ |
| NI 2530 |
| ✓ |
|
| NI 2531 |
| ✓ | ✓ |
| NI 2532 |
| ✓ | ✓ |
| NI 2533 |
| ✓ |
|
| NI 2534 |
| ✓ |
|
| NI 2535 |
| ✓ |
|
| NI 2536 |
| ✓ |
|
| NI 2545 |
| ✓ |
|
| NI 2546 |
| ✓ |
|
| NI 2547 |
| ✓ |
|
| NI 2548 |
| ✓ |
|
| NI 2549 |
| ✓ |
|
| NI 2554 |
| ✓ |
|
| NI 2555 |
| ✓ |
|
| NI 2556 |
| ✓ |
|
| NI 2557 |
| ✓ |
|
| NI 2558 |
| ✓ |
|
| NI 2559 |
| ✓ |
|
| NI 2564 |
| ✓ |
|
| NI 2565 |
| ✓ |
|
| NI 2566 |
| ✓ |
|
| NI 2567 |
| ✓ |
|
| NI 2568 |
| ✓ |
|
| NI 2569 |
| ✓ | ✓ |
| NI 2570 |
| ✓ |
|
| NI 2571 |
| ✓ |
|
| NI 2575 |
| ✓ | ✓ |
| NI 2576 |
| ✓ |
|
| NI 2584 |
| ✓ |
|
| NI 2585 |
| ✓ |
|
| NI 2586 |
| ✓ |
|
| NI 2590 |
| ✓ |
|
| NI 2591 |
| ✓ |
|
| NI 2593 |
| ✓ | ✓ |
| NI 2594 |
| ✓ |
|
| NI 2595 |
| ✓ |
|
| NI 2596 |
| ✓ |
|
| NI 2597 |
| ✓ |
|
| NI 2598 |
| ✓ |
|
| NI 2599 |
| ✓ |
|
| NI 2800 |
| ✓ |
|
| NI 2810 |
| ✓ |
|
| NI 2811 |
| ✓ |
|
| NI 2815 |
| ✓ |
|
| NI 2816 |
| ✓ |
|
SCXI Chassis
The following SCXI Chassis are supported:
| Device | PXI | SCXI |
| NI 1010 | ✓ |
|
| NI 1011 | ✓ |
|
| NI SCXI-1000/DC |
| ✓ |
| NI SCXI-1001 |
| ✓ |
SCXI Modules
The following SCXI modules are supported:
NI SCXI-1100
NI SCXI-1102
NI SCXI-1102B/C
NI SCXI-1104/C
NI SCXI-1112
NI SCXI-1120/D
NI SCXI-1121
NI SCXI-1122
NI SCXI-1124
NI SCXI-1125
NI SCXI-1126
NI SCXI-1127
NI SCXI-1128
NI SCXI-1129
NI SCXI-1130
NI SCXI-1140
NI SCXI-1141
NI SCXI-1142
NI SCXI-1143
NI SCXI-1160
NI SCXI-1161
NI SCXI-1162
NI SCXI-1162HV
NI SCXI-1163
NI SCXI-1163R
NI SCXI-1166
NI SCXI-1167
NI SCXI-1169
NI SCXI-1175
NI SCXI-1190
NI SCXI-1191
NI SCXI-1192
NI SCXI-1193
NI SCXI-1194
NI SCXI-1195
NI SCXI-1314T
NI SCXI-1502
NI SCXI-1503
NI SCXI-1520
NI SCXI-1521/B
NI SCXI-1530
NI SCXI-1531
NI SCXI-1540
NI SCXI-1581
TEDS Interface
The following TEDS devices are supported:
NI SC-2350
NI BNC-2096
NI SCXI-1314T
Academic Devices
The following academic devices are supported:
NI ELVIS II
NI ELVIS II+
NI myDAQ
Legacy DAQ Devices
The following legacy DAQ devices are supported. These do not have NI-DAQmx simulated device capability:
| Device | DAQ Pad | PCI | USB |
| NI DAQPad-6015 | ✓ |
|
|
| NI DAQPad-6016 | ✓ |
|
|
| NI PCI-6013 |
| ✓ |
|
| NI PCI-6014 |
| ✓ |
|
| SensorDAQ |
|
| ✓ |
Low-Cost USB
The following low-cost USB devices are supported. These do not have NI-DAQmx simulated device capability:
| Device | USB |
| NI 6008 | ✓ |
| NI 6009 | ✓ |
| NI TC01 | ✓ |
Devices Not Supported in NI-DAQmx on Windows 7/Vista
The following devices are not supported in NI-DAQmx on Windows 7/Vista (32-bit and 64-bit versions):
The following devices are supported in NI-DAQmx on the 32-bit versions of Windows 7/Vista. They are not supported on the 64-bit versions of Windows 7/Vista:
NI DAQCard-6024E 200 kS/s, 12-bit, 16 analog input channel, two analog output channel, 8 digital I/O line, two counter/timer device
NI DAQCard-6036E 200 kS/s, 16-bit, 16 analog input channel, two analog output channel, 8 digital I/O line, two counter/timer device
NI DAQCard-6062E 500 kS/s, 12-bit, 16 analog input channel device
NI DAQCard-6715 for PCMCIA 1 MS/s 12-bit analog output device
NI DAQCard-DIO-24 for PCMCIA 24-channel 5V/TTL/CMOS digital I/O device
NI SCXI-1600 USB module
System Requirements
| System Use | RAM | Processor |
| Development | 1 GB | Pentium IV or later |
| Deployment | 256 MB | Pentium III/Celeron 600 MHz or Equivalent |
Notice
The mDNSResponder notice is installed with NI-DAQmx. By default, the notice is installed at Program FilesNational InstrumentsSharedmDNS RespondermDNS Responder FOSS notices.doc.
Copyright
Copyright 2003–2011 National Instruments. All rights reserved.
Under the copyright laws, this publication may not be reproduced or transmitted in any form, electronic or mechanical, including photocopying, recording, storing in an information retrieval system, or translating, in whole or in part, without the prior written consent of National Instruments Corporation.
National Instruments respects the intellectual property of others, and we ask our users to do the same. NI software is protected by copyright and other intellectual property laws. Where NI software may be used to reproduce software or other materials belonging to others, you may use NI software only to reproduce materials that you may reproduce in accordance with the terms of any applicable license or other legal restriction.
Trademarks
CVI, LabVIEW, National Instruments, NI, ni.com, the National Instruments corporate logo, and the Eagle logo are trademarks of National Instruments Corporation. Refer to the Trademark Information at ni.com/trademarks for other National Instruments trademarks.
The mark LabWindows is used under a license from Microsoft Corporation. Windows is a registered trademark of Microsoft Corporation in the United States and other countries.
Other product and company names mentioned herein are trademarks or trade names of their respective companies.
Patents
For patents covering the National Instruments products/technology, refer to the appropriate location: Help»Patents in your software, the patents.txt file on your media, or the National Instruments Patent Notice at ni.com/patents.
